Homeowners typically pay for lattice fences based on material choice, fence length, labor time, and site conditions. The price range reflects panel quality, post spacing, and add-ons like gates or decorative caps. This guide presents cost estimates, drivers, and practical budgeting for U.S. buyers seeking lattice fencing.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials (lattice panels, posts, hardware) | $4.50/ft | $9.00/ft | $16.00/ft | Includes panels (wood or vinyl) and posts spaced 6–8 ft apart |
| Labor & installation | $15.00/ft | $28.00/ft | $45.00/ft | Typical crew rate; more for tricky terrain |
| Permits & fees | $0 | $150 | $500 | Depends on local rules and setbacks |
| Delivery/Disposal | $0 | $400 | $1,000 | Distance-dependent |
| Total project (typical yard, 100 ft) | $2,250 | $5,500 | $11,500 | Assumes standard materials and 100 ft of fencing |
Assumptions: region, length, material choice, and labor hours.
Typical Cost Range
Lattice fence pricing varies by material and length. For wood lattice, expect $9–$16 per linear foot for materials and $15–$45 per foot for installed labor, totaling roughly $24–$61 per linear foot combined. Wood lattice commonly costs about $6–$12 per linear foot for panels and pickets plus $9–$28 per foot for skilled labor, while vinyl lattice tends to be in the higher end of the range due to material durability and lighter handling needs.
Cost Breakdown
To illustrate typical components, a 100-foot installation might break down as follows: Materials $900–$1,600, Labor $1,500–$2,800, Permits $0–$300, Delivery/Disposal $0–$500, Total $2,400–$5,200.
| Category | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials | $900 | $1,500 | $2,000 | Wood or vinyl panels and posts |
| Labor | $1,200 | $2,200 | $3,600 | Includes setup, alignment, and post-setting |
| Permits | $0 | $150 | $500 | Local requirement varies |
| Delivery/Disposal | $0 | $200 | $700 | Truck access and waste haul-off |
| Total | $2,100 | $4,050 | $7,000 | Typical residential lot length |
What Drives Price
Key cost drivers include material type (wood vs. vinyl), fence height, and panel design. Higher lattice density increases panel cost and gives less wind passage.
Other important factors are post spacing (6–8 ft is standard), gate inclusion, ground conditions, and existing fencing alignment. Heavier installation terrain, such as sloped yards or rocky soil, raises labor hours and equipment needs.
Regional Price Differences
Prices vary by region due to labor markets and material availability. In the Northeast, installed ranges are typically higher than the Midwest, while the South tends to fall in the middle.
- Urban areas: +10% to +25% on average over national figures
- Suburban: near national averages with modest fluctuations
- Rural: often 5%–15% lower due to lower labor costs
Labor, Hours & Rates
Labor costs for lattice fence installation commonly run $15–$45 per linear foot, depending on crew size and terrain. A straightforward 100-foot run may take 1–2 days for a crew of two, with a per-hour rate effectively around $60–$90 for crew labor when measured by the project.
Labor efficiency improves with pre-cut materials and straight-line alignment. Complex layouts, slopes, or historic properties can push hours higher.
Additional & Hidden Costs
Hidden or extra costs can add $300–$1,000+. Examples include site preparation, concrete footings, staining or sealant, and gate hardware upgrades.
- Site prep: grading, removing existing fencing, or debris removal
- Concrete or anchoring for posts (if required): $150–$400
- Finishes: staining for wood or protective coatings for vinyl
- Gates and hardware upgrades: $150–$600 per gate
Real-World Pricing Examples
Three scenario cards illustrate typical outcomes, with distinct specs and costs.
Basic Scenario
Length: 60 ft; Wood lattice; Standard posts; Manual gates. Labor: 1 day; Materials: $600; Labor: $900; Permits: $0. Total: $1,500. Per-foot: $25.
Mid-Range Scenario
Length: 100 ft; Treated lumber, semi-privacy lattice; Concrete footings; Power tools used. Labor: 1.5 days; Materials: $1,200; Labor: $2,200; Permits: $100; Delivery: $150. Total: $3,650. Per-foot: $36.
Premium Scenario
Length: 120 ft; Vinyl lattice; Premium posts; Custom caps; Gate with hardware; Terrain moderate. Labor: 2 days; Materials: $2,600; Labor: $4,200; Permits: $300; Delivery: $500. Total: $7,600. Per-foot: $63.
Seasonality & Price Trends
Prices tend to rise in spring and early summer when demand for outdoor projects peaks, with occasional dips in late fall and winter in some regions.
Permits, Codes & Rebates
Some jurisdictions require permits for fencing over a certain height or distance. Check local rules and potential rebates for energy-efficient or wood-conservation programs where applicable.
These guidelines provide a practical framework for budgeting lattice fence projects in the United States. They combine per-unit ranges, common installation scenarios, and regional considerations to help buyers estimate costs accurately without overpaying.
